HAS-Motion Software Documentation

User Tools

Site Tools

You are here: Main Page » visual3d » documentation » modeling » marker_sets » OptiTrack Biomech 57 Marker Set
visual3d:documentation:modeling:marker_sets:optitrack_biomech_57_marker_set

Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Both sides previous revisionPrevious revision
Next revision		Previous revision
visual3d:documentation:modeling:marker_sets:optitrack_biomech_57_marker_set [2024/09/06 14:41] – wikisysopvisual3d:documentation:modeling:marker_sets:optitrack_biomech_57_marker_set [2024/09/06 14:45] (current) – wikisysop
Line 265: Line 265:
   ***Do NOT Check:** Offset by Percent (1.0 = 100%)\\   ***Do NOT Check:** Offset by Percent (1.0 = 100%)\\
   ***Check**: Calibration Only Landmark\\   ***Check**: Calibration Only Landmark\\
 +{{ :biomech57-Hand.png?300}}
  
 === Hand Definition === === Hand Definition ===
-{{ :biomech57-Hand.png?300}} 
 **1. Create Left Hand:**\\ **1. Create Left Hand:**\\
 In the **Segments** tab, select //Left Hand// in the Segment Name box.\\ In the **Segments** tab, select //Left Hand// in the Segment Name box.\\
Line 289: Line 289:
  
 === Pelvis Definition === === Pelvis Definition ===
 +{{ :biomech57-pelvis.png?300}}
 **1. Create Pelvis Segment:**\\ **1. Create Pelvis Segment:**\\
 In the **Segments** tab, select //Pelvis// in the Segment Name box.\\ In the **Segments** tab, select //Pelvis// in the Segment Name box.\\
Line 300: Line 300:
 Click on **Build Model.**\\ Click on **Build Model.**\\
 Click on **Close Tab** before proceeding.\\ Click on **Close Tab** before proceeding.\\
-{{ :biomech57-pelvis.png}} 
- 
- 
  
 **2. Modify the [[Visual3D:Documentation:Modeling:Segments:Modify_Segment_Coordinate_System#Modify_Segment_Coordinate_System|Segment Coordinate System]]:**\\ **2. Modify the [[Visual3D:Documentation:Modeling:Segments:Modify_Segment_Coordinate_System#Modify_Segment_Coordinate_System|Segment Coordinate System]]:**\\
Line 312: Line 309:
  
 === Thigh Landmarks === === Thigh Landmarks ===
 +{{ :biomech57-lefthip.png?300}}
 **1. Create LEFT_HIP Joint Center:**\\ **1. Create LEFT_HIP Joint Center:**\\
 Click **Landmarks** button\\ Click **Landmarks** button\\
Line 326: Line 323:
   ***Do NOT Check:** //Offset by Percent (1.0 = 100%)//\\   ***Do NOT Check:** //Offset by Percent (1.0 = 100%)//\\
   ***Do NOT Check:** //Calibration Only Landmark//\\   ***Do NOT Check:** //Calibration Only Landmark//\\
-{{ :biomech57-lefthip.png}}+{{ :biomech57-thigh.png?300}}
  
 === Thigh Definition === === Thigh Definition ===
- 
 **1. Create Left Thigh:**\\ **1. Create Left Thigh:**\\
 In the **Segments** tab, select //Left Thigh// in the Segment Name box.\\ In the **Segments** tab, select //Left Thigh// in the Segment Name box.\\
Line 341: Line 337:
 Click on **Build Model.**\\ Click on **Build Model.**\\
 Click on **Close Tab** before proceeding.\\ Click on **Close Tab** before proceeding.\\
-{{ :biomech57-thigh.png}} 
  
 **2. Modify the [[Visual3D:Documentation:Modeling:Segments:Modify_Segment_Coordinate_System#Modify_Segment_Coordinate_System|Segment Coordinate System]]:**\\ **2. Modify the [[Visual3D:Documentation:Modeling:Segments:Modify_Segment_Coordinate_System#Modify_Segment_Coordinate_System|Segment Coordinate System]]:**\\
Line 351: Line 346:
  
 === Shank Definition === === Shank Definition ===
 +{{ :biomech57-shank.png?300}}
 **1. Create Left Shank:**\\ **1. Create Left Shank:**\\
 In the **Segments** tab, select //Left Shank// in the Segment Name box.\\ In the **Segments** tab, select //Left Shank// in the Segment Name box.\\
Line 363: Line 358:
 Click on **Build Model.**\\ Click on **Build Model.**\\
 Click on **Close Tab** before proceeding. Click on **Close Tab** before proceeding.
-{{ :biomech57-shank.png}} 
  
 **2. Modify the [[Visual3D:Documentation:Modeling:Segments:Modify_Segment_Coordinate_System#Modify_Segment_Coordinate_System|Segment Coordinate System]]:**\\ **2. Modify the [[Visual3D:Documentation:Modeling:Segments:Modify_Segment_Coordinate_System#Modify_Segment_Coordinate_System|Segment Coordinate System]]:**\\
Line 385: Line 379:
 Click on **Build Model.**\\ Click on **Build Model.**\\
 Click on **Close Tab** before proceeding.\\  Click on **Close Tab** before proceeding.\\ 
-{{ :biomech57-shank.png}} 
  
 **2. Modify the [[Visual3D:Documentation:Modeling:Segments:Modify_Segment_Coordinate_System#Modify_Segment_Coordinate_System|Segment Coordinate System]]:**\\ **2. Modify the [[Visual3D:Documentation:Modeling:Segments:Modify_Segment_Coordinate_System#Modify_Segment_Coordinate_System|Segment Coordinate System]]:**\\
visual3d/documentation/modeling/marker_sets/optitrack_biomech_57_marker_set.1725633667.txt.gz · Last modified: 2024/09/06 14:41 by wikisysop