visual3d:documentation:pipeline:event_commands:event_maximum
Differences
This shows you the differences between two versions of the page.
Both sides previous revisionPrevious revisionNext revision | Previous revision | ||
visual3d:documentation:pipeline:event_commands:event_maximum [2025/04/28 19:18] – [Dialog] wikisysop | visual3d:documentation:pipeline:event_commands:event_maximum [2025/04/29 19:04] (current) – wikisysop | ||
---|---|---|---|
Line 81: | Line 81: | ||
**Select Frame Offset:** 0\\ | **Select Frame Offset:** 0\\ | ||
**Signal Components: | **Signal Components: | ||
- | **Event Sequence: | ||
**Event Sequence Instance: | **Event Sequence Instance: | ||
- | {{:Event_Max_RKFlex_MaxLocal.jpg?400}} | + | |{{:visual3d: |
+ | Event_Maximum | ||
+ | / | ||
+ | / | ||
+ | / | ||
+ | / | ||
+ | / | ||
+ | ! / | ||
+ | ! / | ||
+ | ! / | ||
+ | ! / | ||
+ | ! / | ||
+ | ! / | ||
+ | ! / | ||
+ | ! / | ||
+ | ! / | ||
+ | / | ||
+ | ! / | ||
+ | ; | ||
+ | </ | ||
2. Close the dialog, on the Signals and Events tab, select the desired signal from the data tree, in this case **Right_Knee_Angle**. Navigate into the LINK_MODEL_BASED items folder, and select the checkbox beside the signal. | 2. Close the dialog, on the Signals and Events tab, select the desired signal from the data tree, in this case **Right_Knee_Angle**. Navigate into the LINK_MODEL_BASED items folder, and select the checkbox beside the signal. | ||
Line 92: | Line 110: | ||
{{: | {{: | ||
- | **RKFlex_Max** will be created at the minimum value during the gait cycle within | + | **RKFlex_MaxLocal** will be created at the maximum values |
+ | |||
+ | |{{: | ||
+ | |||
+ | |||
+ | ==== Example 2: Complex ==== | ||
+ | |||
+ | In this example, | ||
+ | |||
+ | Use the Event_Maximum command to find the peaks in the acceleration signal, the component is set to Y and frame window | ||
+ | |||
+ | The signal used to represent the acceleration was taken from the KINETIC_KINEMATIC folder - RFT (Right Foot) | ||
+ | |||
+ | < | ||
+ | Event_Maximum | ||
+ | / | ||
+ | / | ||
+ | / | ||
+ | / | ||
+ | / | ||
+ | ! / | ||
+ | ! / | ||
+ | / | ||
+ | ! / | ||
+ | ! / | ||
+ | ! / | ||
+ | ! / | ||
+ | ! / | ||
+ | ! / | ||
+ | / | ||
+ | ! / | ||
+ | ; | ||
+ | </ | ||
+ | |||
+ | Then use Metric_Signal_Value_At_Event to extract the actual Y-acceleration values at these peaks for analysis: | ||
+ | |||
+ | < | ||
+ | Metric_Signal_Value_At_Event | ||
+ | / | ||
+ | / | ||
+ | / | ||
+ | ! / | ||
+ | / | ||
+ | ! / | ||
+ | / | ||
+ | ! / | ||
+ | / | ||
+ | ! / | ||
+ | ! / | ||
+ | ! / | ||
+ | ! / | ||
+ | ! / | ||
+ | ! / | ||
+ | ! / | ||
+ | ; | ||
+ | </ | ||
- | ---- | ||
===== Notes ===== | ===== Notes ===== | ||
visual3d/documentation/pipeline/event_commands/event_maximum.1745867917.txt.gz · Last modified: 2025/04/28 19:18 by wikisysop