HAS-Motion Software Documentation

User Tools

Site Tools

You are here: Main Page » visual3d » documentation » pipeline » file_commands » Export Polygon Trunk Example
visual3d:documentation:pipeline:file_commands:export_polygon_trunk_example

Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Both sides previous revisionPrevious revision
Next revision		Previous revision
visual3d:documentation:pipeline:file_commands:export_polygon_trunk_example [2024/07/12 14:03] – created sgrangervisual3d:documentation:pipeline:file_commands:export_polygon_trunk_example [2024/07/17 15:45] (current) – created sgranger
Line 1: Line 1:
-====== Export_Polygon_Trunk_Example ======+====== Export Polygon Trunk Example ======
  
 \\ \\
Line 18: Line 18:
 A CMO file where the trunk is defined using "Typical Convention" can be downloaded [[https://www.has-motion.com/download/examples/Export_Polygon/PolygonExport.zip|here]]. The file "SampleWorkspace_Typical.cmo" contains the trunk described below. A CMO file where the trunk is defined using "Typical Convention" can be downloaded [[https://www.has-motion.com/download/examples/Export_Polygon/PolygonExport.zip|here]]. The file "SampleWorkspace_Typical.cmo" contains the trunk described below.
  
-|\\ \\ \\ \\ The **proximal** end of the trunk (RTA_PROX) is the mid point between the C7 and jugular notch targets (CV7 and SJN).\\ \\ The **distal** end of the trunk is the mid point between the lower back and the xiphoid process targets (ULB_MID and SXS).\\ \\ The **lateral** orientation of the trunk (RTA_LAT) is defined along the line between the right and left acromion targets (LCAJ and RCAJ).  |  {{PolygonExport_TypicalConv.png}}|+|\\ \\ \\ \\ The **proximal** end of the trunk (RTA_PROX) is the mid point between the C7 and jugular notch targets (CV7 and SJN).\\ \\ The **distal** end of the trunk is the mid point between the lower back and the xiphoid process targets (ULB_MID and SXS).\\ \\ The **lateral** orientation of the trunk (RTA_LAT) is defined along the line between the right and left acromion targets (LCAJ and RCAJ).  |  {{:PolygonExport_TypicalConv.png}}|
  
 ==== Polygon Convention ==== ==== Polygon Convention ====
Line 24: Line 24:
 A CMO file where the trunk is defined using the "Polygon Convention" can be downloaded [[https://www.has-motion.com/download/examples/Export_Polygon/PolygonExport.zip|here]]. The file "SampleWorkspace_Polygon.cmo" contains the trunk described below. A CMO file where the trunk is defined using the "Polygon Convention" can be downloaded [[https://www.has-motion.com/download/examples/Export_Polygon/PolygonExport.zip|here]]. The file "SampleWorkspace_Polygon.cmo" contains the trunk described below.
  
-|\\ \\ \\ \\ The **proximal** end of the trunk is the mid point between the lower back and the xiphoid process targets (ULB_MID and SXS).\\ \\ The **distal** end of the trunk (RTA_PROX) is the mid point between the C7 and jugular notch targets (CV7 and SJN).\\ \\ The **medial** orientation of the trunk (RTA_LAT) is defined along the line between the right and left acromion targets (LCAJ and RCAJ).  |  {{PolygonExport_PolygonConv.png}}|+|\\ \\ \\ \\ The **proximal** end of the trunk is the mid point between the lower back and the xiphoid process targets (ULB_MID and SXS).\\ \\ The **distal** end of the trunk (RTA_PROX) is the mid point between the C7 and jugular notch targets (CV7 and SJN).\\ \\ The **medial** orientation of the trunk (RTA_LAT) is defined along the line between the right and left acromion targets (LCAJ and RCAJ).  |  {{:PolygonExport_PolygonConv.png}}|
  
 ==== Coordinate System Orientation ==== ==== Coordinate System Orientation ====
  
-|\\ \\ \\ \\ If the segment has been defined correctly, the origin should be just below the ribs.\\ \\ The orientation of the segment coordinate system should be aligned with the coordinate systems of the other segments in the model. In the image, the coordinate systems was rotated so that +Z is up and +X is mediolateral. Instructions to rotate a coordinate system can be found [[Visual3D:Documentation:Modeling:Segments:Modify_Segment_Coordinate_System|here]].  |  {{PolygonExport_SegmentGeometry.png}}|+|\\ \\ \\ \\ If the segment has been defined correctly, the origin should be just below the ribs.\\ \\ The orientation of the segment coordinate system should be aligned with the coordinate systems of the other segments in the model. In the image, the coordinate systems was rotated so that +Z is up and +X is mediolateral. Instructions to rotate a coordinate system can be found [[Visual3D:Documentation:Modeling:Segments:Modify_Segment_Coordinate_System|here]].  |  {{:PolygonExport_SegmentGeometry.png}}|
  
 \\ \\
Line 37: Line 37:
 The default image for the thorax/ab segment includes the lumbar. Since these segments are not included in the Polygon convention, you may want to modify the graphic image in the Segment Properties tab. Please note, this is only for aesthetics. The default image for the thorax/ab segment includes the lumbar. Since these segments are not included in the Polygon convention, you may want to modify the graphic image in the Segment Properties tab. Please note, this is only for aesthetics.
  
-|\\ \\ \\ \\ Click the "Browse" button next to "Model File:" and search for the "thoraciccerviclet12toacromium.v3g" file in the "Visual3D v5\Models" folder.\\ \\ Click the "Rotate/Scale Graphic Model" button and set the "Clockwise Rotation" to 180.  |  {{PolygonExport_SegmentProperties.png}}|+|\\ \\ \\ \\ Click the "Browse" button next to "Model File:" and search for the "thoraciccerviclet12toacromium.v3g" file in the "Visual3D v5\Models" folder.\\ \\ Click the "Rotate/Scale Graphic Model" button and set the "Clockwise Rotation" to 180.  |  {{:PolygonExport_SegmentProperties.png}}|
  
 ==== References ==== ==== References ====
visual3d/documentation/pipeline/file_commands/export_polygon_trunk_example.1720792992.txt.gz · Last modified: 2024/07/12 14:03 by sgranger