HAS-Motion Software Documentation

User Tools

Site Tools

You are here: Main Page » visual3d » documentation » pipeline » metric_commands » Metric Event Count
visual3d:documentation:pipeline:metric_commands:metric_event_count

Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Both sides previous revisionPrevious revision
Next revision		Previous revision
visual3d:documentation:pipeline:metric_commands:metric_event_count [2024/06/18 13:31] – sgrangervisual3d:documentation:pipeline:metric_commands:metric_event_count [2024/07/17 15:46] (current) – created sgranger
Line 1: Line 1:
 +====== Metric Event Count ======
 +
 Creates a metric containing the number of events that occur in an event sequence or time interval. Creates a metric containing the number of events that occur in an event sequence or time interval.
  
Line 10: Line 12:
 /GENERATE_COUNT_TOTAL_IN_GLOBAL=TRUE /GENERATE_COUNT_TOTAL_IN_GLOBAL=TRUE
 **;** **;**
-===== Prior to Version 5.00.29 =====+==== Prior to Version 5.00.29 ====
  
 the user could select "either" an **Event_Sequence/Exclude Sequence** or a **Time_Interval** the user could select "either" an **Event_Sequence/Exclude Sequence** or a **Time_Interval**
Line 18: Line 20:
 A count of events within each time interval (starting from Time=0) is specified as a separate frame. A count of events within each time interval (starting from Time=0) is specified as a separate frame.
 For example, if there were three ranges defined by the time sequence, there would be 3 frames of data in the resulting metric. For example, if there were three ranges defined by the time sequence, there would be 3 frames of data in the resulting metric.
-===== Starting in Version 5.00.29 =====+==== Starting in Version 5.00.29 ====
  
 the user can select both an **Event_Sequence/Exclude Sequence** and a **Time_Interval** but only the first Event_Sequence is used. the user can select both an **Event_Sequence/Exclude Sequence** and a **Time_Interval** but only the first Event_Sequence is used.
Line 26: Line 28:
 As of Visual3Dv5.00.29 this command must be edited manually. As of Visual3Dv5.00.29 this command must be edited manually.
  
-===== User Dialog Starting in Version 5.01.14 =====+==== User Dialog Starting in Version 5.01.14 ====
  
-|In Visual3D v5.01.14 the user dialog was introduced. The command works the same as described in v5.00.29, however the user may now modify the command using the GUI interface.  |  {{MetricEventCountDialog.png}}|+|In Visual3D v5.01.14 the user dialog was introduced. The command works the same as described in v5.00.29, however the user may now modify the command using the GUI interface.  |  {{:MetricEventCountDialog.png}}|
  
-===== Example_1 =====+==== Example_1 ====
  
 **Select_Active_File** **Select_Active_File**
Line 48: Line 50:
  
  
-==== Result ====+=== Result ===
  
 LON_COUNT will count all events in the file and a metric value LON_COUNT will be created in the METRIC::PROCESSED folder. LON_COUNT will count all events in the file and a metric value LON_COUNT will be created in the METRIC::PROCESSED folder.
Line 55: Line 57:
  
 To see this value set the Active File to GLOBAL and a metric value LON_COUNT will be created in the METRIC::PROCESSED folder. To see this value set the Active File to GLOBAL and a metric value LON_COUNT will be created in the METRIC::PROCESSED folder.
-===== Example_2 =====+==== Example_2 ====
  
 **This example shows 3 ways the Metric_Event_Count command can be used.** **This example shows 3 ways the Metric_Event_Count command can be used.**
Line 78: Line 80:
 2.140000 2.140000
 3.360000 3.360000
-==== Count events across entire file ====+=== Count events across entire file ===
  
 **Count across the entire file** **Count across the entire file**
Line 100: Line 102:
 Event_Count= 3 Event_Count= 3
 Global_Event_Count= 12 Global_Event_Count= 12
-==== Count events across entire file in time intervals ====+=== Count events across entire file in time intervals ===
  
 **Count across the entire file at 1 second intervals** **Count across the entire file at 1 second intervals**
Line 143: Line 145:
 Global_Event_Count= 4 Global_Event_Count= 4
 Global_Event_Count= 0 Global_Event_Count= 0
-==== Count events in a set number of intervals across entire file ====+=== Count events in a set number of intervals across entire file ===
  
 **Count over 5 intervals from the event_sequence START+END** **Count over 5 intervals from the event_sequence START+END**
visual3d/documentation/pipeline/metric_commands/metric_event_count.1718717514.txt.gz · Last modified: 2024/06/18 13:31 by sgranger