Differences

This shows you the differences between two versions of the page.

--- visual3d:tutorials:modeling:plug-in_gait_lower_limb [2024/11/15 19:47] – [Conventional Gait Model Decisions] wikisysop
+++ visual3d:tutorials:modeling:plug-in_gait_lower_limb [2024/12/10 15:06] (current) – [Hip Joint Center] wikisysop
@@ Line 27: / Line 27: @@
 {{:Conventional_gait_model_decisions1.png?790}}
-In the case of the Plug-In Gait, the decisions have already been made for option 2(c), 4(b) and 5(b). Using Visual3D, it is possible to opt for different model decisions if needed or relevant. This would however not be consistent with the Plug-In Gait's implementation per se.
+In the case of the Plug-In Gait, the decisions have already been made for option 2%%(c)%%, 4(b) and 5(b). Using Visual3D, it is possible to opt for different model decisions if needed or relevant. This would however not be consistent with the Plug-In Gait's implementation per se.
 ==== Manual Metrics For Plug-In Gait ====
@@ Line 100: / Line 100: @@
 {{:tutorial1_2.jpg}}\\
-  - From the **Model** menu, select **Create (Add Static Calibration File)**\\
+  - From the **Model** menu, select **Hybrid Model from C3DFile**
-  - Select **Hybrid Model from C3DFile**
+  - In the **Select the calibration file for the new model** dialog, select //WalkingStaticLowerBody.c3d//
-  - In the **Select the calibration file for the new model** dialog, select //Sub01_Static_01.c3d//
     - If using a knee alignment device, select //Sub01_Static_KAD_01.c3d//
   - Click **Open.**
@@ Line 192: / Line 191: @@
   - Click **Landmarks** button
   - Click **Add New Landmark** button
-  - Create Landmark: //RHIP//\\ \\ **Landmark Name:** //RHIP//\\ **Define Orientation Using:** \\    Click **Existing Segment:** //Pelvis// \\ Offset Using the Following **ML/AP/AXIAL** Offsets:\\    **X:** //-HJC_ML//    **Y:** //HJC_AP//    **Z:** //HJC_AX// \\ **Do NOT Check:** //Offset by Percent (1.0 = 100%)// \\ **Check:** //Calibration Only Landmark//
+  - Create Landmark: //RHIP//\\ \\ **Landmark Name:** //RHIP//\\ **Define Orientation Using:** \\    Click **Existing Segment:** //Pelvis// \\ Offset Using the Following **ML/AP/AXIAL** Offsets:\\    **X:** //-HJC_ML//    **Y:** //HJC_AP//    **Z:** //HJC_AX// \\ **Do NOT Check:** //Offset by Percent (1.0 = 100%)// \\ **Do NOT Check:** //Calibration Only Landmark//
 ----
@@ Line 201: / Line 200: @@
   - Click **Landmarks** button
   - Click **Add New Landmark** button
-  - Create Landmark: //LHIP//\\ \\ **Landmark Name:** //LHIP//\\ **Define Orientation Using:** \\    Click **Existing Segment:** //Pelvis//\\ Offset Using the Following **ML/AP/AXIAL** Offsets:\\    **X:** //HJC_ML//    **Y:** //HJC_AP//    **Z:** //HJC_AX// \\ **Do NOT Check:** //Offset by Percent (1.0 = 100%)// \\ **Check:** //Calibration Only Landmark//
+  - Create Landmark: //LHIP//\\ \\ **Landmark Name:** //LHIP//\\ **Define Orientation Using:** \\    Click **Existing Segment:** //Pelvis//\\ Offset Using the Following **ML/AP/AXIAL** Offsets:\\    **X:** //HJC_ML//    **Y:** //HJC_AP//    **Z:** //HJC_AX// \\ **Do NOT Check:** //Offset by Percent (1.0 = 100%)// \\ **Do NOT Check:** //Calibration Only Landmark//
 ----
@@ Line 240: / Line 239: @@
   - In the **Segments** tab, select //Right Thigh// in the Segment Name box.
   - Click on the **Create Segment** button.
-  - In the **Right Thigh** tab, enter these values:\\ \\ **Define Proximal Joint and Radius**\\    **Lateral:** //None//     **Joint:** //RHJC//     **Medial:** //None//     \\    **Radius:** //0.5*DISTANCE(RHJC,LHJC)//\\ **Define Distal Joint and Radius**\\    **Lateral:** //RKNE//     **Joint:** //None//     **Medial:** //None//     \\    **Radius:** //0.5*Knee_Width + MarkerRadius//\\ **Extra Target to Define Orientation**\\    **Location:** //Lateral//     //RTHI//\\ **Select Tracking Targets:**\\ **Check:** //Use Calibration Targets for Tracking//\\ \\
+  - In the **Right Thigh** tab, enter these values:\\ \\ **Define Proximal Joint and Radius**\\    **Lateral:** //None//     **Joint:** //RHJC//     **Medial:** //None//     \\    **Radius:** //0.5*DISTANCE(RHJC,LHJC)//\\ **Define Distal Joint and Radius**\\    **Lateral:** //RKNE//     **Joint:** //None//     **Medial:** //None//     \\    **Radius:** //0.5*Knee_Width + MarkerRadius//\\ **Extra Target to Define Orientation**\\    **Location:** //Lateral//     //RTHI// \\ **Select Tracking Targets:**\\ **Check:** //Use Calibration Targets for Tracking//\\ \\
   - Click on **Build Model.**
   - Click on **Close Tab** before proceeding.