Differences

This shows you the differences between two versions of the page.

--- visual3d:tutorials:modeling:plug-in_gait_lower_limb [2024/12/10 14:35] – [Load Static Trial] wikisysop
+++ visual3d:tutorials:modeling:plug-in_gait_lower_limb [2024/12/10 15:06] (current) – [Hip Joint Center] wikisysop
@@ Line 191: / Line 191: @@
   - Click **Landmarks** button
   - Click **Add New Landmark** button
-  - Create Landmark: //RHIP//\\ \\ **Landmark Name:** //RHIP//\\ **Define Orientation Using:** \\    Click **Existing Segment:** //Pelvis// \\ Offset Using the Following **ML/AP/AXIAL** Offsets:\\    **X:** //-HJC_ML//    **Y:** //HJC_AP//    **Z:** //HJC_AX// \\ **Do NOT Check:** //Offset by Percent (1.0 = 100%)// \\ **Check:** //Calibration Only Landmark//
+  - Create Landmark: //RHIP//\\ \\ **Landmark Name:** //RHIP//\\ **Define Orientation Using:** \\    Click **Existing Segment:** //Pelvis// \\ Offset Using the Following **ML/AP/AXIAL** Offsets:\\    **X:** //-HJC_ML//    **Y:** //HJC_AP//    **Z:** //HJC_AX// \\ **Do NOT Check:** //Offset by Percent (1.0 = 100%)// \\ **Do NOT Check:** //Calibration Only Landmark//
 ----
@@ Line 200: / Line 200: @@
   - Click **Landmarks** button
   - Click **Add New Landmark** button
-  - Create Landmark: //LHIP//\\ \\ **Landmark Name:** //LHIP//\\ **Define Orientation Using:** \\    Click **Existing Segment:** //Pelvis//\\ Offset Using the Following **ML/AP/AXIAL** Offsets:\\    **X:** //HJC_ML//    **Y:** //HJC_AP//    **Z:** //HJC_AX// \\ **Do NOT Check:** //Offset by Percent (1.0 = 100%)// \\ **Check:** //Calibration Only Landmark//
+  - Create Landmark: //LHIP//\\ \\ **Landmark Name:** //LHIP//\\ **Define Orientation Using:** \\    Click **Existing Segment:** //Pelvis//\\ Offset Using the Following **ML/AP/AXIAL** Offsets:\\    **X:** //HJC_ML//    **Y:** //HJC_AP//    **Z:** //HJC_AX// \\ **Do NOT Check:** //Offset by Percent (1.0 = 100%)// \\ **Do NOT Check:** //Calibration Only Landmark//
 ----
@@ Line 239: / Line 239: @@
   - In the **Segments** tab, select //Right Thigh// in the Segment Name box.
   - Click on the **Create Segment** button.
-  - In the **Right Thigh** tab, enter these values:\\ \\ **Define Proximal Joint and Radius**\\    **Lateral:** //None//     **Joint:** //RHJC//     **Medial:** //None//     \\    **Radius:** //0.5*DISTANCE(RHJC,LHJC)//\\ **Define Distal Joint and Radius**\\    **Lateral:** //RKNE//     **Joint:** //None//     **Medial:** //None//     \\    **Radius:** //0.5*Knee_Width + MarkerRadius//\\ **Extra Target to Define Orientation**\\    **Location:** //Lateral//     //RTHI//\\ **Select Tracking Targets:**\\ **Check:** //Use Calibration Targets for Tracking//\\ \\
+  - In the **Right Thigh** tab, enter these values:\\ \\ **Define Proximal Joint and Radius**\\    **Lateral:** //None//     **Joint:** //RHJC//     **Medial:** //None//     \\    **Radius:** //0.5*DISTANCE(RHJC,LHJC)//\\ **Define Distal Joint and Radius**\\    **Lateral:** //RKNE//     **Joint:** //None//     **Medial:** //None//     \\    **Radius:** //0.5*Knee_Width + MarkerRadius//\\ **Extra Target to Define Orientation**\\    **Location:** //Lateral//     //RTHI// \\ **Select Tracking Targets:**\\ **Check:** //Use Calibration Targets for Tracking//\\ \\
   - Click on **Build Model.**
   - Click on **Close Tab** before proceeding.